ONLINE HELP SOPAS Chapter 5

LECTOR®620

Parameters

If the reading gate is open, the LECTOR

620 records images with a frequency of 60 Hz and

evaluates these by codes. Ideally, at least one code will have been completely recorded and

identified on an image. If the reading gate is closed, no images are recorded.

Signal sources for opening the reading gate:

• S

ENSOR / RESULT 1: A signal at digital input 1 (e.g. via a light barrier) opens the reading

gate.

• S

ENSOR / RESULT 2: A signal at digital input 2 (e.g. via a light barrier) opens the reading

gate.

• E

XTERNAL INPUT 1: A signal at external digital input 1 (e.g. via a light barrier) opens the rea-

ding gate.

• E

XTERNAL INPUT 2: A signal at external digital input 2 (e.g. via a light barrier) opens the rea-

ding gate.

• SOPAS C

OMMAND: A command to open the reading gate is expected e.g. from an external

controller (PLC). (A detailed list of the command language is available from SICK on re-

quest.)

• A

UTO CYCLE: The reading gate is opened and closed automatically after a defined cycle

(using the Pulse and Pause parameters) (e.g. if the feed speed stays the same and the code

position is constant or for manual code reading)

• CAN: The signal for opening and closing the reading gate is expected via the CAN inter-

face. In a network of devices that communicate with each other via the CAN network, the

signal for opening the reading gate can be distributed. For this, a suitable trigger signal is

received by a device (usually the master) and distributed to the other CAN network.

• U

SER DEFINED COMMAND: You can freely define a command for opening the reading gate,

which is e.g. generated by an external controller (PLC) and transmitted to the LECTOR

620.

• F

REE RUNNING: The reading gate is permanently open. As a result, manual code reading is

possible without an external trigger signal (e.g. from a light barrier). Signals for opening/clo-

sing the reading gate are ignored. As it is therefore not possible to define a specific point in

time for data output, a signal for N

O READ cannot be output. The time of output and the rea-

ding speed depend on the degree of utilization of the LECTOR

620.

5.4.2.1.4 Stop delay

You can use the Stop delay parameter to influence the time for closing the reading gate. The

unit can be selected in the Trigger delay parameter.

A positive value enables the reading gate to be closed later, e.g. to extend the evaluation

period for codes at the rear of an object.

•

B. STOP DELAY (additional time/distance for which the reading gate remains open after

event B)

1 2 ... 32 33 34 35 36 37 38 39 40 41 42 ... 165 166

Komentarze do niniejszej Instrukcji

Brak uwag

Star-dreams Stinger GX-77 manuels

Manuels d'utilisation et guides de l'utilisateur pour Capteurs Star-dreams Stinger GX-77.
Nous fournissons des manuels en pdf 1 Star-dreams Stinger GX-77 à télécharger gratuitement par type de document : Manuel de l'utilisateur

Star dreams Stinger GX-77 Manuel de l'utilisateur (6 pages)

marque: Star-dreams | Catégorie: Sensors | Taille: 0.62 MB |

Table des matières

STINGER

ПОДГОТОВКА ПРИБОРА К РАБОТЕ

РЕЖИМЫ РАБОТЫ

 «▼ENT» 

 «▼ENT»   «▼ENT»

И СБЕРЕЖЕНИЕ

Адреса сервисных центров

Plus de produits et de manuels pour Capteurs Star-dreams

Modèles	Type de document
Crunch 3150	Manuel de l'utilisateur Инструкция по эксплуатации Star Dreams Crunch 3150, 5 pages
Star Pro 10	Manuel de l'utilisateur Инструкция по эксплуатации Star Dreams Star Pro 10, 4 pages
Crunch Q25	Manuel de l'utilisateur Инструкция по эксплуатации Star Dreams Crunch Q25, 5 pages
Crunch 2170	Manuel de l'utilisateur Инструкция по эксплуатации Star Dreams Crunch 2170, 6 pages
Crunch 221B	Manuel de l'utilisateur Инструкция по эксплуатации Star Dreams Crunch 221B, 4 pages
Stinger S650 ST	Manuel de l'utilisateur Инструкция по эксплуатации Star Dreams Stinger S650 ST, 6 pages
Stinger S155 ST	Manuel de l'utilisateur Инструкция по эксплуатации Star Dreams Stinger S155 ST, 5 pages
Star Pro 40	Manuel de l'utilisateur Инструкция по эксплуатации Star Dreams Star Pro 40, 4 pages
Stinger Sunrise	Manuel de l'utilisateur Инструкция по эксплуатации Star Dreams Stinger Sunrise, 6 pages
LKT RD-10	Manuel de l'utilisateur Инструкция по эксплуатации Star Dreams LKT RD-10, 4 pages
Star 2005	Manuel de l'utilisateur Инструкция по эксплуатации Star Dreams Star 2005, 3 pages
Star 2012	Manuel de l'utilisateur Инструкция по эксплуатации Star Dreams Star 2012, 5 pages
Stinger RX-85 STM	Manuel de l'utilisateur Инструкция по эксплуатации Star Dreams Stinger RX-85 STM, 7 pages
Crunch Q25 STR	Manuel de l'utilisateur Инструкция по эксплуатации Star Dreams Crunch Q25 STR, 5 pages
Crunch Q65	Manuel de l'utilisateur Инструкция по эксплуатации Star Dreams Crunch Q65, 5 pages
LKT RD-15	Manuel de l'utilisateur Инструкция по эксплуатации Star Dreams LKT RD-15, 4 pages
Stinger RX-75 ST	Manuel de l'utilisateur Инструкция по эксплуатации Star Dreams Stinger RX-75 ST, 7 pages
Star X41	Manuel de l'utilisateur Инструкция по эксплуатации Star Dreams Star X41, 4 pages
Star Pro 60	Manuel de l'utilisateur Инструкция по эксплуатации Star Dreams Star Pro 60, 5 pages
Stinger RX-65	Manuel de l'utilisateur Инструкция по эксплуатации Star Dreams Stinger RX-65, 6 pages

Code Corporation Code Reader 1.1 Informacje Techniczne Strona 37

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Czytniki kodów kreskowych Code Corporation Code Reader 1.1

Star-dreams Stinger GX-77 manuels

Star dreams Stinger GX-77 Manuel de l'utilisateur (6 pages)

Table des matières

Plus de produits et de manuels pour Capteurs Star-dreams